What to do when the heat goes out in Washington, MO

Step 1 of 3: Equipment

First, check the thermostat is set to heat and the batteries aren't dead, and check the breaker box for a tripped switch. If the furnace runs on electric heat strips, which is how most homes in Washington and Franklin County warm up, a tripped breaker or a blown fuse is the most common reason it stops cold. If power is fine and the blower won't run at all, the problem is likely in the electric heating elements or the control board, and that calls for a repair visit rather than a reset. Don't wait long to deal with it. A Franklin County winter can drop a house into the 50s overnight once the heat is out, and that's hard on pipes as well as people. Once you know it isn't a simple breaker fix, the next step is getting a contractor out to look at the furnace itself.

A beige high-efficiency furnace with two white PVC pipes stands beside sheet-metal ductwork and a concrete wall in an empty basement with a bare light-colored wall and concrete floor.

Why electric heat strips trip breakers

Electric heat strips pull a lot of current when they kick on, more than most other parts of the system. A breaker that trips once might have been overloaded for a moment. One that trips again as soon as you reset it points to a short in the strips themselves or in the blower motor that pushes air across them. Either way, a tripped breaker that won't stay reset means the furnace needs a look before it runs again.

A gray furnace with sheet-metal ductwork and white PVC vent pipes stands in the corner of a finished basement room with a blank beige wall and concrete floor.

What the blower motor does

The blower motor is what moves air through the heat strips and out into your ducts. If it's weak or failing, the strips can overheat because the heat isn't being carried away fast enough, which is why some furnaces have a safety switch that shuts the strips off if airflow drops too low. A furnace that clicks on and off without blowing warm air often points to the blower, not the strips.

Why does the house feel cold but the air still blows?

Walk up to a vent and feel the air moving, but it is not warm. That points to the blower running while the heat strips stay off. You might notice the breaker for the furnace keeps tripping, or the air has a faint burning smell when it first kicks on, which can mean dust burning off strips that have not run in a while, or it can mean something more. Rooms farthest from the furnace will cool first and stay cold longest. If this goes on for days in a Franklin County winter, pipes near outside walls are at some risk of freezing, and that is worth paying attention to before it becomes its own problem.

A woman with dark hair in a bun wearing a cream knit sweater sits on a gray sofa in a bright living room, looking off to the side.
A woman wrapped in a knit blanket sits on a gray sofa in a living room, looking toward a bright window with houseplants and an armchair in the background.
A woman in a gray cowl-neck sweater sits on a light sofa with cushions, smiling and looking to the side, with a kitchen and window visible behind her.
A woman with dark hair in a bun, wearing a light linen shirt, sits on a sofa and looks to the side, with a window, houseplants and a kitchen with pendant lights blurred behind her.

Get matched with a furnace pro in Franklin County

A furnace that won't heat on a cold night in Washington doesn't wait for a good time to get fixed, and most homes here lean on electric heat strips with no backup fuel to fall back on. Once you've checked the thermostat and the breaker and the problem is still there, the next step is someone who can get into the furnace itself and find out whether it's the heat strips, a bad sequencer, or something upstream in the wiring. Finding that person usually means searching around, calling a few numbers, explaining the same problem more than once, then sitting with quotes trying to figure out who actually knows what they're doing. Handing that off here means you describe it once and a contractor who works on furnaces in Franklin County reaches out to you directly. With the house cold and electric heat strips the only thing standing between you and a warm house, that's time worth not spending on the phone.

You can wait and keep resetting the breaker, hoping it holds overnight while you watch the thermostat and layer on blankets until someone can look at it.

Or you can get a contractor out to find out why the heat strips are drawing too much current, because a breaker that keeps tripping usually means something in the system is already failing, not the breaker itself.

How cold does it get when your furnace quits in Washington?

  • Winter nights average 24°F

    Winter nights here average 24°F. If the furnace stops heating, there's no mild stretch to wait out until morning.

  • Heat runs October through April

    Heat runs here from October through April. A furnace that fails isn't a summer problem you can put off.

  • 67.6% of homes heat with electricity

    67.6% of homes in Franklin County heat with electricity, mostly through electric heat strips, so a tripped breaker can mean no backup heat source at all.

NOAA nClimDiv 1991-2020 · ACS 2020-2024

Where this leaves you

  • A thermostat set wrong or a tripped breaker explains some no-heat calls, and both take a minute to check before anything else.
  • A breaker that trips again right after you reset it means the heat strips are drawing more current than the circuit can carry.
  • Blower air that stays cool points to the heat strips not coming on at all, even while the fan runs normally.
  • Most homes in Washington and Franklin County lean on electric heat strips with no gas furnace to fall back on.
  • Winter nights here average 24°F, so a furnace that quits overnight needs a real fix, not another reset.
  • Sorting out which part failed, the breaker, the strips, or something else in the circuit, calls for a contractor's eyes on the system.

A furnace that won't heat in Washington usually comes down to one of a few things. Check the thermostat first, then the breaker box. If the breaker holds, something downstream of it is still wrong. If it trips again as soon as you reset it, the heat strips are pulling more current than that circuit can handle, and resetting it again won't change that. Blower air that stays cool even though the fan runs tells you the strips aren't firing at all. None of these are guesses you can settle by watching the vent or waiting out the night. Franklin County homes mostly run on electric heat strips with nothing else to fall back on, so when they fail, the house has no backup heat source warming it while you sort things out. With winter nights here averaging 24°F, that's not something to leave for a few days.

Getting to the actual cause, a bad breaker, worn heat strips, or a wiring problem somewhere in between, takes someone who can test the circuit, not just look at it. That also means you don't have to be the one who finds that person. Instead of searching through contractor listings, calling a handful of them, explaining the tripped breaker and the cold air from the vent to each one, then lining up their quotes side by side, you can skip straight to a contractor who already knows the kind of system most houses around here run and what tends to go wrong with it.

A gray furnace with PVC vent pipes and sheet-metal ductwork stands against a wall in an unfinished basement with concrete floor and walls, exposed wood joists, and a small window.

A local pro for your furnace repair

Start one form

Describe your furnace job once, to one pro.

It costs nothing to send, and you don't have to hire anyone.